Seagate Freeagent Dockstar: Unterschied zwischen den Versionen

Aus DL8RDS Wiki
Wechseln zu: Navigation, Suche
(→‎Procedure)
Zeile 19: Zeile 19:
 
       RX TX GND 3.3V!
 
       RX TX GND 3.3V!
  
−
So when you now boot up the device, you'll get the following output in the terminal (Linux: minicom):
+
Now do the following steps:
  
−
  U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)                                            
+
* Connect the Freeagent to your DHCP router, but don't connect it to the internet! The Freeagent shall receive an IP address, but it shall not be able to phone home!
−
                                                                                                         
+
* Start your terminal client (Linux: minicom), and don't forget to disable Hardware Flow Control in minicom!!
 +
 
 +
So when you now boot up the device, you'll get the following output in the terminal:
 +
 
 +
  U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
 +
 
  U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60
 
  U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60
 
   
 
   
Zeile 42: Zeile 47:
 
  Streaming disabled  
 
  Streaming disabled  
 
  Write allocate disabled
 
  Write allocate disabled
−
 
+
 
   
 
   
 
  USB 0: host mode
 
  USB 0: host mode
Zeile 61: Zeile 66:
 
     Entry Point:  00008000
 
     Entry Point:  00008000
 
     Verifying Checksum ... OK
 
     Verifying Checksum ... OK
−
  OK
+
  OK  
 
   
 
   
 
  Starting kernel ...  
 
  Starting kernel ...  
Zeile 210: Zeile 215:
 
  [    3.090000]    arm4regs  :  1084.000 MB/sec
 
  [    3.090000]    arm4regs  :  1084.000 MB/sec
 
  [    3.140000]    8regs    :  754.800 MB/sec
 
  [    3.140000]    8regs    :  754.800 MB/sec
−
  [    3.190000]    32regs    :  899.600 MB/sec
+
  [    3.190000]    32regs    :  890.400 MB/sec
 
  [    3.190000] raid5: using function: arm4regs (1084.000 MB/sec)
 
  [    3.190000] raid5: using function: arm4regs (1084.000 MB/sec)
 
  [    3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
 
  [    3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Zeile 225: Zeile 230:
 
  [    3.250000] md: ... autorun DONE.
 
  [    3.250000] md: ... autorun DONE.
 
  [    7.870000] Empty flash at 0x00de8e44 ends at 0x00de9000
 
  [    7.870000] Empty flash at 0x00de8e44 ends at 0x00de9000
−
  [    8.030000] VFS: Mounted root (jffs2 filesystem) readonly.
+
  [    8.020000] VFS: Mounted root (jffs2 filesystem) readonly.
 
  [    8.030000] Freeing init memory: 120K
 
  [    8.030000] Freeing init memory: 120K
−
  [    8.120000] scsi 0:0:0:0: Direct-Access              USB DISK 2.0    PMAP PQ: 0 ANSI: 4
+
  [    8.050000] scsi 0:0:0:0: Direct-Access              USB DISK 2.0    PMAP PQ: 0 ANSI: 4
−
  [    8.950000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
+
  [    8.150000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
−
  [    8.960000] sd 0:0:0:0: [sda] Write Protect is off
+
  [    8.160000] sd 0:0:0:0: [sda] Write Protect is off
−
  [    8.960000] sd 0:0:0:0: [sda] Assuming drive cache: write through
+
  [    8.160000] sd 0:0:0:0: [sda] Assuming drive cache: write through
−
  [    9.010000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
+
  [    8.210000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
−
  [    9.030000] sd 0:0:0:0: [sda] Write Protect is off
+
  [    8.220000] sd 0:0:0:0: [sda] Write Protect is off
−
  [    9.030000] sd 0:0:0:0: [sda] Assuming drive cache: write through
+
  [    8.220000] sd 0:0:0:0: [sda] Assuming drive cache: write through
−
  [    9.040000]  sda: sda1
+
  [    8.230000]  sda: sda1
−
  [    9.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk
+
  [    8.240000] sd 0:0:0:0: [sda] Attached SCSI removable disk
−
  [    9.270000] sd 0:0:0:0: Attached scsi generic sg0 type 0
+
  [    8.240000] sd 0:0:0:0: Attached scsi generic sg0 type 0
 
  init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
 
  init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
 
  starting pid 285, tty '': '/etc/init.d/rcS'
 
  starting pid 285, tty '': '/etc/init.d/rcS'
Zeile 246: Zeile 251:
 
  PIP1 87
 
  PIP1 87
 
  Sending discover...
 
  Sending discover...
−
  [  13.280000] eth0: link up, full duplex, speed 1 Gbps
+
  [  11.860000] eth0: link up, full duplex, speed 100 Mbps
−
Sending discover...
 
 
  Sending discover...
 
  Sending discover...
 +
Sending select for 192.168.178.24...
 +
Lease of 192.168.178.24 obtained, lease time 864000
 
  HWADDR 00 0x10 0x75 0x1a 0xc0 0x57
 
  HWADDR 00 0x10 0x75 0x1a 0xc0 0x57
 
  PIP0 192
 
  PIP0 192
 
  PIP1 87
 
  PIP1 87
−
  Unexpected Argument: leasefail
+
  eth0      Link encap:Ethernet HWaddr 00:10:75:1A:C0:57  
−
  interface=eth0
+
          inet addr:192.168.178.24 Bcast:192.168.178.255 Mask:255.255.255.0
−
PATH=/sbin:/usr/sbin:/bin:/usr/bin
+
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
−
  PWD=/
+
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
−
SHLVL=1
+
          TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
−
HOME=/
+
          collisions:0 txqueuelen:532
−
_=/bin/printenv
+
          RX bytes:1240 (1.2 KiB)  TX bytes:1180 (1.1 KiB)
−
No lease, forking to background
+
          Interrupt:11
−
Loading fs modules:         [  19.400000] fuse init (API version 7.8)
+
   
−
  Success
+
  eth0:0    Link encap:Ethernet HWaddr 00:10:75:1A:C0:57  
−
[  19.780000] ufsd: module license 'Commercial product' taints kernel.
+
          inet addr:169.254.192.87 Bcast:169.254.255.255 Mask:255.255.0.0
−
[  19.940000] ufsd: driver loaded at bf040000 built on Aug 5 2009 15:35:26
+
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
−
[  19.940000] UFSD version 7.07 (Aug  5 2009, 15:29:19)
+
          Interrupt:11
−
[  19.940000] NTFS read/write support included
+
   
−
  [  19.940000] Hfs+/HfsX read/write support included
+
  starting pid 339, tty '': '/bin/sh'
−
  [  19.940000] $Id: ufsdvfs.c,v 1.226 2009/07/30 16:04:07 shura Exp $ (LBD=ON)
+
  -sh-3.2#  
−
Loading tun.ko:             [  19.960000] tun: Universal TUN/TAP device driver, 1.6
+
 
−
[  19.970000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
+
 
−
Success
+
You may also find out its address if you look at the router GUI or if you use
−
Loading xce.ko:             [  19.990000] Cloud Engines XCE Init [Version: 1.0.0.20]
+
fping -g 192.168.0.0/24
−
[  20.000000] XCE: CPU MEMORY MAP:
+
 
−
[  20.000000] XCE:   -- 0x00001000 - 0xbeffffff (3055 MB)  User Space Mappings
+
So when you know the IP, you can now log into the Freeagent using
−
[  20.010000] XCE:   -- 0xbf000000 - 0xbfffffff ( 16 MB)  Kernel module space
+
  ssh root@(Freeagent-IP)
−
[  20.020000] XCE:  -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram
+
  Passwd: stxadmin
−
[  20.020000] XCE:   -- 0xc8800000 - 0xe7ffffff ( 504 MB)  Kernel vmalloc space
+
 
−
  [  20.030000] XCE:  -- 0xe8000000 - 0xfeffffff ( 367 MB)  Kernel platform space
+
If you have plugged in a USB stick, you may see it with mount:
−
  [  20.040000] XCE: Current GPIO State:
 
−
  [  20.040000] XCE: GPIO L OUT:   0xeff00000
 
−
[  20.050000] XCE: GPIO L OE:     0xefffffff
 
−
[  20.050000] XCE:  GPIO L BLINK: 0x00000000
 
−
[  20.060000] XCE: GPIO L POL:   0x00000000
 
−
[  20.060000] XCE:  GPIO L IN:    0xeff00080
 
−
[  20.060000] XCE: GPIO H OUT:   0xfffeffff
 
−
[  20.070000] XCE:  GPIO H OE:    0xfffc3fff
 
−
[  20.070000] XCE:  GPIO H BLINK:  0x00000000
 
−
[  20.080000] XCE:  GPIO H POL:    0x00000000
 
−
  [  20.080000] XCE:  GPIO H IN:     0x0002fffd
 
−
[  20.080000] XCE: Kernel thread starting PID: 353
 
−
Success
 
−
[  20.090000] XCE:   -- 'wdog=off
 
−
  [  20.090000] '
 
−
Starting hbplug:            Success
 
−
  starting pid 355, tty '': '/bin/sh'
 
−
  -sh-3.2# [  21.080000] XCE: BLPARAMS:  -- Loading properties [c707ff04].
 
−
[  21.090000] XCE: BLPARAMS: reading 2048 bytes @ a0000
 
−
  [  21.100000] XCE: BLPARAMS: reading 2048 bytes @ a0800
 
−
  [  21.100000] XCE: BLPARAMS: reading 2048 bytes @ a1000
 
−
[  21.110000] XCE: BLPARAMS: reading 2048 bytes @ a1800
 
−
[  26.290000] XCE:   -- 'led0=0'
 

Version vom 24. Dezember 2011, 17:17 Uhr

I am using a Seagate Freeagent Dockstar disk station as a fully fledged server at DB0ZM. Here are the pictures.

1 Pictures

Freeagent1.jpg

Freeagent2.jpg

2 Links

3 Procedure

First you need to connecto to the serial port. For this purpose you use an Arduino style level shifter with 3,3V which you connect to the pins 6, 4, 2: 

 9  7  5  3  1 
10  8  6  4  2
      RX TX GND 3.3V!

Now do the following steps:

  • Connect the Freeagent to your DHCP router, but don't connect it to the internet! The Freeagent shall receive an IP address, but it shall not be able to phone home!
  • Start your terminal client (Linux: minicom), and don't forget to disable Hardware Flow Control in minicom!!

So when you now boot up the device, you'll get the following output in the terminal: 

U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 00690D60

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz 

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 128MB 
DRAM Total size 128MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:1.0

Streaming disabled 
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0 

NAND read: device 0 offset 0x100000, size 0x300000

Reading data from 0x3ff800 -- 100% complete.
 3145728 bytes read: OK
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2009-08-31  23:31:05 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1976384 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK 

Starting kernel ... 

Uncompressing Linux............................................................................................................................ done, booting the kernel.
[    0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #57 Mon Aug 31 16:31:01 PDT 2009
[    0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] Machine: Feroceon-KW
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] CPU0: D VIVT write-back cache
[    0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[    0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[    0.000000] Built 1 zonelists.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total
[    0.000000] Memory: 125824KB available (3588K code, 252K data, 120K init)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] CPU: Testing write buffer coherency: ok
[    0.240000] NET: Registered protocol family 16
[    0.240000] 
[    0.240000] CPU Interface
[    0.240000] -------------
[    0.240000] SDRAM_CS0 ....base 00000000, size 128MB 
[    0.240000] SDRAM_CS1 ....disable
[    0.240000] SDRAM_CS2 ....disable
[    0.240000] SDRAM_CS3 ....disable
[    0.240000] PEX0_MEM ....base e8000000, size 128MB 
[    0.240000] PEX0_IO ....base f2000000, size   1MB 
[    0.240000] INTER_REGS ....base f1000000, size   1MB 
[    0.240000] NFLASH_CS ....base fa000000, size   2MB 
[    0.240000] SPI_CS ....base f4000000, size  16MB 
[    0.240000] BOOT_ROM_CS ....no such
[    0.240000] DEV_BOOTCS ....no such
[    0.240000] CRYPT_ENG ....base f0000000, size   2MB 
[    0.240000] 
[    0.240000]   Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG  Soc: 88F6281 A0 LE
[    0.240000] 
[    0.240000]  Detected Tclk 200000000 and SysClk 400000000 
[    0.240000] MV Buttons Device Load
[    0.240000] Marvell USB EHCI Host controller #0: c0537600
[    0.740000] PEX0 interface detected no Link.
[    0.740000] PCI: bus0: Fast back to back transfers enabled
[    0.740000] SCSI subsystem initialized
[    0.740000] usbcore: registered new interface driver usbfs
[    0.740000] usbcore: registered new interface driver hub
[    0.740000] usbcore: registered new device driver usb
[    0.740000] NET: Registered protocol family 2
[    0.750000] Time: kw_clocksource clocksource has been installed.
[    0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.840000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.840000] TCP reno registered
[    0.870000] RTC has been updated!!!
[    0.870000] RTC registered
[    0.870000] Use the XOR engines (acceleration) for enhancing the following functions:
[    0.870000]   o RAID 5 Xor calculation
[    0.870000]   o kernel memcpy
[    0.870000]   o kenrel memzero
[    0.870000] Number of XOR engines to use: 4
[    0.870000] cesadev_init(c00116b4)
[    0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    0.870000] MV Buttons Driver Load
[    0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[    0.870000] squashfs: LZMA suppport for slax.org by jro
[    0.870000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc.
[    0.870000] io scheduler noop registered
[    0.870000] io scheduler anticipatory registered (default)
[    0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[    0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    0.900000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[    0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[    0.910000] Loading Marvell Ethernet Driver:
[    0.920000]   o Cached descriptors in DRAM
[    0.920000]   o DRAM SW cache-coherency
[    0.920000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    0.930000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    0.940000]   o TCP segmentation offload enabled
[    0.940000]   o Receive checksum offload enabled
[    0.940000]   o Transmit checksum offload enabled
[    0.950000]   o Network Fast Processing (Routing) supported
[    0.960000]   o Driver ERROR statistics enabled
[    0.960000]   o Driver INFO statistics enabled
[    0.960000]   o Proc tool API enabled
[    0.970000]   o Rx descripors: q0=128
[    0.970000]   o Tx descripors: q0=532
[    0.980000]   o Loading network interface(s):
[    0.980000]     o eth0, ifindex = 1, GbE port = 0
[    0.990000]     o eth1, ifindex = 2, GbE port = 1
[    0.990000] 
[    1.000000] mvFpRuleDb (c7ed5000): 1024 entries, 4096 bytes
[    1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[    1.010000] Copyright (c) 1999-2006 Intel Corporation.
[    1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[    1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[    1.020000] 
[    1.020000] Warning Sata is Powered Off
[    1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[    1.040000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[    1.050000] Scanning device for bad blocks
[    1.140000] Bad eraseblock 1825 at 0x0e420000
[    1.150000] Using static partition definition
[    1.160000] Creating 4 MTD partitions on "nand_mtd":
[    1.160000] 0x00000000-0x00100000 : "u-boot"
[    1.170000] 0x00100000-0x00500000 : "uImage"
[    1.170000] 0x00500000-0x02500000 : "root"
[    1.180000] 0x02500000-0x10000000 : "data"
[    1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[    1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[    1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[    1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    1.250000] usb usb1: configuration #1 chosen from 1 choice
[    1.260000] hub 1-0:1.0: USB hub found
[    1.260000] hub 1-0:1.0: 1 port detected
[    1.380000] USB Universal Host Controller Interface driver v3.0
[    1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[    1.810000] usb 1-1: configuration #1 chosen from 1 choice
[    1.810000] hub 1-1:1.0: USB hub found
[    1.820000] hub 1-1:1.0: 4 ports detected
[    2.170000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3
[    2.270000] usb 1-1.2: configuration #1 chosen from 1 choice
[    2.280000] usbcore: registered new interface driver usblp
[    2.280000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[    2.290000] Initializing USB Mass Storage driver...
[    2.300000] scsi0 : SCSI emulation for USB Mass Storage devices
[    2.300000] usbcore: registered new interface driver usb-storage
[    2.310000] USB Mass Storage support registered.
[    2.310000] mice: PS/2 mouse device common for all mice
[    2.320000] i2c /dev entries driver
[    2.320000] Linux telephony interface: v1.00
[    2.330000] md: linear personality registered for level -1
[    2.330000] md: raid0 personality registered for level 0
[    2.340000] md: raid1 personality registered for level 1
[    2.510000] raid6: int32x1     97 MB/s
[    2.680000] raid6: int32x2    114 MB/s
[    2.850000] raid6: int32x4    122 MB/s
[    3.020000] raid6: int32x8    110 MB/s
[    3.020000] raid6: using algorithm int32x4 (122 MB/s)
[    3.020000] md: raid6 personality registered for level 6
[    3.030000] md: raid5 personality registered for level 5
[    3.030000] md: raid4 personality registered for level 4
[    3.040000] raid5: measuring checksumming speed
[    3.090000]    arm4regs  :  1084.000 MB/sec
[    3.140000]    8regs     :   754.800 MB/sec
[    3.190000]    32regs    :   890.400 MB/sec
[    3.190000] raid5: using function: arm4regs (1084.000 MB/sec)
[    3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[    3.200000] dm_crypt using the OCF package.
[    3.210000] sdhci: Secure Digital Host Controller Interface driver
[    3.210000] sdhci: Copyright(c) Pierre Ossman
[    3.220000] usbcore: registered new interface driver usbhid
[    3.220000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[    3.230000] TCP cubic registered
[    3.230000] NET: Registered protocol family 1
[    3.240000] NET: Registered protocol family 17
[    3.240000] md: Autodetecting RAID arrays.
[    3.250000] md: autorun ...
[    3.250000] md: ... autorun DONE.
[    7.870000] Empty flash at 0x00de8e44 ends at 0x00de9000
[    8.020000] VFS: Mounted root (jffs2 filesystem) readonly.
[    8.030000] Freeing init memory: 120K
[    8.050000] scsi 0:0:0:0: Direct-Access              USB DISK 2.0     PMAP PQ: 0 ANSI: 4
[    8.150000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
[    8.160000] sd 0:0:0:0: [sda] Write Protect is off
[    8.160000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.210000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB)
[    8.220000] sd 0:0:0:0: [sda] Write Protect is off
[    8.220000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.230000]  sda: sda1
[    8.240000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.240000] sd 0:0:0:0: Attached scsi generic sg0 type 0
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 285, tty : '/etc/init.d/rcS'
[   10.200000] eth0: link down
[   10.200000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x10 0x75 0x1a 0xc0 0x57
PIP0 192
PIP1 87
Sending discover...
[   11.860000] eth0: link up, full duplex, speed 100 Mbps
Sending discover...
Sending select for 192.168.178.24...
Lease of 192.168.178.24 obtained, lease time 864000
HWADDR 00 0x10 0x75 0x1a 0xc0 0x57
PIP0 192
PIP1 87
eth0      Link encap:Ethernet  HWaddr 00:10:75:1A:C0:57  
          inet addr:192.168.178.24  Bcast:192.168.178.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:532 
          RX bytes:1240 (1.2 KiB)  TX bytes:1180 (1.1 KiB)
          Interrupt:11 

eth0:0    Link encap:Ethernet  HWaddr 00:10:75:1A:C0:57  
          inet addr:169.254.192.87  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          Interrupt:11 

starting pid 339, tty : '/bin/sh'
-sh-3.2#


You may also find out its address if you look at the router GUI or if you use 

fping -g 192.168.0.0/24

So when you know the IP, you can now log into the Freeagent using 

ssh root@(Freeagent-IP)
Passwd: stxadmin

If you have plugged in a USB stick, you may see it with mount:

Abgerufen von „http://www.dl8rds.de/index.php?title=Seagate_Freeagent_Dockstar&oldid=1889“