Fonera Router: Unterschied zwischen den Versionen
Dl8rds (Diskussion | Beiträge) |
Dl8rds (Diskussion | Beiträge) |
||
Zeile 15: | Zeile 15: | ||
Hacking it is extremely simple. Just follow the instructions given [http://sodoityourself.com/accessing-serial-console-on-the-fon here] and connect a level shifter correctly and you will get access to the Redboot BIOS. The only little difficulty I ran into was to keep any kind of flow control switched off. If HW flow control should still be "on", you cannot write to the console and entering CTRL-C will not cause Redboot to come up. | Hacking it is extremely simple. Just follow the instructions given [http://sodoityourself.com/accessing-serial-console-on-the-fon here] and connect a level shifter correctly and you will get access to the Redboot BIOS. The only little difficulty I ran into was to keep any kind of flow control switched off. If HW flow control should still be "on", you cannot write to the console and entering CTRL-C will not cause Redboot to come up. | ||
+ | +PHY ID is 0022:5521 | ||
Ethernet eth0: MAC address 00:18:84:19:09:bc | Ethernet eth0: MAC address 00:18:84:19:09:bc | ||
IP: 0.0.0.0/255.255.255.255, Gateway: 0.0.0.0 | IP: 0.0.0.0/255.255.255.255, Gateway: 0.0.0.0 |
Version vom 5. August 2008, 20:42 Uhr
My brother gave me a FONERA router which I will make into a WLAN link station soon. Here are the important links I have collected:
- http://wiki.openwrt.org/OpenWrtDocs/Hardware/Fon/Fonera
- http://sodoityourself.com/accessing-serial-console-on-the-fon
- http://jauzsi.hu/2006/10/13/inside-of-the-fonera
- http://www.dd-wrt.com/wiki/index.php/LaFonera_Hardware_Serial-Cable-Port
- http://www.flickr.com/photos/mother/261623405/sizes/o/
- http://www.larsen-b.com/Article/262.html
I intend to use the FONERA router as remote little box to serve a WLAN link, but also to handle a packet radio Terminal Node Controller. Because it is a little hard to have software running on it, I want it to make its ttyS0 available over the network to my core box... ser2net seems an interesting way to go.
- http://www.nwlab.net/tutorials/ser2net/konsolenserver-linux.html
- http://forum.openwrt.org/viewtopic.php?id=13161
Hacking it is extremely simple. Just follow the instructions given here and connect a level shifter correctly and you will get access to the Redboot BIOS. The only little difficulty I ran into was to keep any kind of flow control switched off. If HW flow control should still be "on", you cannot write to the console and entering CTRL-C will not cause Redboot to come up.
+PHY ID is 0022:5521 Ethernet eth0: MAC address 00:18:84:19:09:bc IP: 0.0.0.0/255.255.255.255, Gateway: 0.0.0.0 Default server: 0.0.0.0 RedBoot(tm) bootstrap and debug environment [ROMRAM] Non-certified release, version v1.3.0 - built 16:57:58, Aug 7 2006 Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. Board: ap51 RAM: 0x80000000-0x81000000, [0x80040450-0x80fe1000] available FLASH: 0xa8000000 - 0xa87f0000, 128 blocks of 0x00010000 bytes each. == Executing boot script in 1.000 seconds - enter ^C to abort == Executing boot script in 1.000 seconds - enter ^C to abort == Executing boot script in 1.000 seconds - enter ^C to abort ^C RedBoot> ^C RedBoot> ^C RedBoot>