Seagate Freeagent Dockstar: Unterschied zwischen den Versionen
Aus DL8RDS Wiki
Dl8rds (Diskussion | Beiträge) |
Dl8rds (Diskussion | Beiträge) |
||
Zeile 11: | Zeile 11: | ||
* http://blogdoch.net/index.php?entry=entry100405-203729 Installing Ubuntu | * http://blogdoch.net/index.php?entry=entry100405-203729 Installing Ubuntu | ||
* http://www.yourwarrantyisvoid.com/2010/07/14/hardware-porn-seagate-dockstar-teardown/ good pictures! | * http://www.yourwarrantyisvoid.com/2010/07/14/hardware-porn-seagate-dockstar-teardown/ good pictures! | ||
+ | |||
+ | == Procedure == | ||
+ | First you need to connecto to the serial port. For this purpose you use an Arduino style level shifter with 3,3V which you connect to the pins 6, 4, 2: | ||
+ | |||
+ | 9 7 5 3 1 | ||
+ | 10 8 6 4 2 | ||
+ | RX TX GND 3.3V! | ||
+ | |||
+ | So when you now boot up the device, you'll get the following output in the terminal (Linux: minicom): | ||
+ | |||
+ | U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) | ||
+ | |||
+ | U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 | ||
+ | |||
+ | Soc: 88F6281 A0 (DDR2) | ||
+ | CPU running @ 1200Mhz L2 running @ 400Mhz | ||
+ | SysClock = 400Mhz , TClock = 200Mhz | ||
+ | |||
+ | DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 | ||
+ | DRAM CS[0] base 0x00000000 size 128MB | ||
+ | DRAM Total size 128MB 16bit width | ||
+ | Flash: 0 kB | ||
+ | Addresses 8M - 0M are saved for the U-Boot usage. | ||
+ | Mem malloc Initialization (8M - 7M): Done | ||
+ | NAND:256 MB | ||
+ | |||
+ | CPU : Marvell Feroceon (Rev 1) | ||
+ | CLOUD ENGINES BOARD: REDSTONE:1.0 | ||
+ | |||
+ | Streaming disabled | ||
+ | Write allocate disabled | ||
+ | |||
+ | |||
+ | USB 0: host mode | ||
+ | PEX 0: interface detected no Link. | ||
+ | Net: egiga0 [PRIME], egiga1 | ||
+ | Hit any key to stop autoboot: 0 | ||
+ | |||
+ | NAND read: device 0 offset 0x100000, size 0x300000 | ||
+ | |||
+ | Reading data from 0x3ff800 -- 100% complete. | ||
+ | 3145728 bytes read: OK | ||
+ | ## Booting image at 00800000 ... | ||
+ | Image Name: Linux-2.6.22.18 | ||
+ | Created: 2009-08-31 23:31:05 UTC | ||
+ | Image Type: ARM Linux Kernel Image (uncompressed) | ||
+ | Data Size: 1976384 Bytes = 1.9 MB | ||
+ | Load Address: 00008000 | ||
+ | Entry Point: 00008000 | ||
+ | Verifying Checksum ... OK | ||
+ | OK | ||
+ | |||
+ | Starting kernel ... | ||
+ | |||
+ | Uncompressing Linux............................................................................................................................ done, booting the kernel. | ||
+ | [ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #57 Mon Aug 31 16:31:01 PDT 2009 | ||
+ | [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 | ||
+ | [ 0.000000] Machine: Feroceon-KW | ||
+ | [ 0.000000] Using UBoot passing parameters structure | ||
+ | [ 0.000000] Memory policy: ECC disabled, Data cache writeback | ||
+ | [ 0.000000] CPU0: D VIVT write-back cache | ||
+ | [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | [ 0.000000] Built 1 zonelists. Total pages: 32512 | ||
+ | [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro | ||
+ | [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) | ||
+ | [ 0.000000] Console: colour dummy device 80x30 | ||
+ | [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) | ||
+ | [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) | ||
+ | [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total | ||
+ | [ 0.000000] Memory: 125824KB available (3588K code, 252K data, 120K init) | ||
+ | [ 0.240000] Mount-cache hash table entries: 512 | ||
+ | [ 0.240000] CPU: Testing write buffer coherency: ok | ||
+ | [ 0.240000] NET: Registered protocol family 16 | ||
+ | [ 0.240000] | ||
+ | [ 0.240000] CPU Interface | ||
+ | [ 0.240000] ------------- | ||
+ | [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB | ||
+ | [ 0.240000] SDRAM_CS1 ....disable | ||
+ | [ 0.240000] SDRAM_CS2 ....disable | ||
+ | [ 0.240000] SDRAM_CS3 ....disable | ||
+ | [ 0.240000] PEX0_MEM ....base e8000000, size 128MB | ||
+ | [ 0.240000] PEX0_IO ....base f2000000, size 1MB | ||
+ | [ 0.240000] INTER_REGS ....base f1000000, size 1MB | ||
+ | [ 0.240000] NFLASH_CS ....base fa000000, size 2MB | ||
+ | [ 0.240000] SPI_CS ....base f4000000, size 16MB | ||
+ | [ 0.240000] BOOT_ROM_CS ....no such | ||
+ | [ 0.240000] DEV_BOOTCS ....no such | ||
+ | [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB | ||
+ | [ 0.240000] | ||
+ | [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE | ||
+ | [ 0.240000] | ||
+ | [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 | ||
+ | [ 0.240000] MV Buttons Device Load | ||
+ | [ 0.240000] Marvell USB EHCI Host controller #0: c0537600 | ||
+ | [ 0.740000] PEX0 interface detected no Link. | ||
+ | [ 0.740000] PCI: bus0: Fast back to back transfers enabled | ||
+ | [ 0.740000] SCSI subsystem initialized | ||
+ | [ 0.740000] usbcore: registered new interface driver usbfs | ||
+ | [ 0.740000] usbcore: registered new interface driver hub | ||
+ | [ 0.740000] usbcore: registered new device driver usb | ||
+ | [ 0.740000] NET: Registered protocol family 2 | ||
+ | [ 0.750000] Time: kw_clocksource clocksource has been installed. | ||
+ | [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | ||
+ | [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) | ||
+ | [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) | ||
+ | [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) | ||
+ | [ 0.840000] TCP reno registered | ||
+ | [ 0.870000] RTC has been updated!!! | ||
+ | [ 0.870000] RTC registered | ||
+ | [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: | ||
+ | [ 0.870000] o RAID 5 Xor calculation | ||
+ | [ 0.870000] o kernel memcpy | ||
+ | [ 0.870000] o kenrel memzero | ||
+ | [ 0.870000] Number of XOR engines to use: 4 | ||
+ | [ 0.870000] cesadev_init(c00116b4) | ||
+ | [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 | ||
+ | [ 0.870000] MV Buttons Driver Load | ||
+ | [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher | ||
+ | [ 0.870000] squashfs: LZMA suppport for slax.org by jro | ||
+ | [ 0.870000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc. | ||
+ | [ 0.870000] io scheduler noop registered | ||
+ | [ 0.870000] io scheduler anticipatory registered (default) | ||
+ | [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled | ||
+ | [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | ||
+ | [ 0.900000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | ||
+ | [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize | ||
+ | [ 0.910000] Loading Marvell Ethernet Driver: | ||
+ | [ 0.920000] o Cached descriptors in DRAM | ||
+ | [ 0.920000] o DRAM SW cache-coherency | ||
+ | [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 | ||
+ | [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 | ||
+ | [ 0.940000] o TCP segmentation offload enabled | ||
+ | [ 0.940000] o Receive checksum offload enabled | ||
+ | [ 0.940000] o Transmit checksum offload enabled | ||
+ | [ 0.950000] o Network Fast Processing (Routing) supported | ||
+ | [ 0.960000] o Driver ERROR statistics enabled | ||
+ | [ 0.960000] o Driver INFO statistics enabled | ||
+ | [ 0.960000] o Proc tool API enabled | ||
+ | [ 0.970000] o Rx descripors: q0=128 | ||
+ | [ 0.970000] o Tx descripors: q0=532 | ||
+ | [ 0.980000] o Loading network interface(s): | ||
+ | [ 0.980000] o eth0, ifindex = 1, GbE port = 0 | ||
+ | [ 0.990000] o eth1, ifindex = 2, GbE port = 1 | ||
+ | [ 0.990000] | ||
+ | [ 1.000000] mvFpRuleDb (c7ed5000): 1024 entries, 4096 bytes | ||
+ | [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI | ||
+ | [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. | ||
+ | [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI | ||
+ | [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation | ||
+ | [ 1.020000] | ||
+ | [ 1.020000] Warning Sata is Powered Off | ||
+ | [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ | ||
+ | [ 1.040000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) | ||
+ | [ 1.050000] Scanning device for bad blocks | ||
+ | [ 1.140000] Bad eraseblock 1825 at 0x0e420000 | ||
+ | [ 1.150000] Using static partition definition | ||
+ | [ 1.160000] Creating 4 MTD partitions on "nand_mtd": | ||
+ | [ 1.160000] 0x00000000-0x00100000 : "u-boot" | ||
+ | [ 1.170000] 0x00100000-0x00500000 : "uImage" | ||
+ | [ 1.170000] 0x00500000-0x02500000 : "root" | ||
+ | [ 1.180000] 0x02500000-0x10000000 : "data" | ||
+ | [ 1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | ||
+ | [ 1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | ||
+ | [ 1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | ||
+ | [ 1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 | ||
+ | [ 1.250000] usb usb1: configuration #1 chosen from 1 choice | ||
+ | [ 1.260000] hub 1-0:1.0: USB hub found | ||
+ | [ 1.260000] hub 1-0:1.0: 1 port detected | ||
+ | [ 1.380000] USB Universal Host Controller Interface driver v3.0 | ||
+ | [ 1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2 | ||
+ | [ 1.810000] usb 1-1: configuration #1 chosen from 1 choice | ||
+ | [ 1.810000] hub 1-1:1.0: USB hub found | ||
+ | [ 1.820000] hub 1-1:1.0: 4 ports detected | ||
+ | [ 2.170000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3 | ||
+ | [ 2.270000] usb 1-1.2: configuration #1 chosen from 1 choice | ||
+ | [ 2.280000] usbcore: registered new interface driver usblp | ||
+ | [ 2.280000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver | ||
+ | [ 2.290000] Initializing USB Mass Storage driver... | ||
+ | [ 2.300000] scsi0 : SCSI emulation for USB Mass Storage devices | ||
+ | [ 2.300000] usbcore: registered new interface driver usb-storage | ||
+ | [ 2.310000] USB Mass Storage support registered. | ||
+ | [ 2.310000] mice: PS/2 mouse device common for all mice | ||
+ | [ 2.320000] i2c /dev entries driver | ||
+ | [ 2.320000] Linux telephony interface: v1.00 | ||
+ | [ 2.330000] md: linear personality registered for level -1 | ||
+ | [ 2.330000] md: raid0 personality registered for level 0 | ||
+ | [ 2.340000] md: raid1 personality registered for level 1 | ||
+ | [ 2.510000] raid6: int32x1 97 MB/s | ||
+ | [ 2.680000] raid6: int32x2 114 MB/s | ||
+ | [ 2.850000] raid6: int32x4 122 MB/s | ||
+ | [ 3.020000] raid6: int32x8 110 MB/s | ||
+ | [ 3.020000] raid6: using algorithm int32x4 (122 MB/s) | ||
+ | [ 3.020000] md: raid6 personality registered for level 6 | ||
+ | [ 3.030000] md: raid5 personality registered for level 5 | ||
+ | [ 3.030000] md: raid4 personality registered for level 4 | ||
+ | [ 3.040000] raid5: measuring checksumming speed | ||
+ | [ 3.090000] arm4regs : 1084.000 MB/sec | ||
+ | [ 3.140000] 8regs : 754.800 MB/sec | ||
+ | [ 3.190000] 32regs : 899.600 MB/sec | ||
+ | [ 3.190000] raid5: using function: arm4regs (1084.000 MB/sec) | ||
+ | [ 3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com | ||
+ | [ 3.200000] dm_crypt using the OCF package. | ||
+ | [ 3.210000] sdhci: Secure Digital Host Controller Interface driver | ||
+ | [ 3.210000] sdhci: Copyright(c) Pierre Ossman | ||
+ | [ 3.220000] usbcore: registered new interface driver usbhid | ||
+ | [ 3.220000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver | ||
+ | [ 3.230000] TCP cubic registered | ||
+ | [ 3.230000] NET: Registered protocol family 1 | ||
+ | [ 3.240000] NET: Registered protocol family 17 | ||
+ | [ 3.240000] md: Autodetecting RAID arrays. | ||
+ | [ 3.250000] md: autorun ... | ||
+ | [ 3.250000] md: ... autorun DONE. | ||
+ | [ 7.870000] Empty flash at 0x00de8e44 ends at 0x00de9000 | ||
+ | [ 8.030000] VFS: Mounted root (jffs2 filesystem) readonly. | ||
+ | [ 8.030000] Freeing init memory: 120K | ||
+ | [ 8.120000] scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 | ||
+ | [ 8.950000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB) | ||
+ | [ 8.960000] sd 0:0:0:0: [sda] Write Protect is off | ||
+ | [ 8.960000] sd 0:0:0:0: [sda] Assuming drive cache: write through | ||
+ | [ 9.010000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB) | ||
+ | [ 9.030000] sd 0:0:0:0: [sda] Write Protect is off | ||
+ | [ 9.030000] sd 0:0:0:0: [sda] Assuming drive cache: write through | ||
+ | [ 9.040000] sda: sda1 | ||
+ | [ 9.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk | ||
+ | [ 9.270000] sd 0:0:0:0: Attached scsi generic sg0 type 0 | ||
+ | init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST) | ||
+ | starting pid 285, tty '': '/etc/init.d/rcS' | ||
+ | [ 10.200000] eth0: link down | ||
+ | [ 10.200000] eth0: started | ||
+ | udhcpc (v1.7.0) started | ||
+ | HWADDR 00 0x10 0x75 0x1a 0xc0 0x57 | ||
+ | PIP0 192 | ||
+ | PIP1 87 | ||
+ | Sending discover... | ||
+ | [ 13.280000] eth0: link up, full duplex, speed 1 Gbps | ||
+ | Sending discover... | ||
+ | Sending discover... | ||
+ | HWADDR 00 0x10 0x75 0x1a 0xc0 0x57 | ||
+ | PIP0 192 | ||
+ | PIP1 87 | ||
+ | Unexpected Argument: leasefail | ||
+ | interface=eth0 | ||
+ | PATH=/sbin:/usr/sbin:/bin:/usr/bin | ||
+ | PWD=/ | ||
+ | SHLVL=1 | ||
+ | HOME=/ | ||
+ | _=/bin/printenv | ||
+ | No lease, forking to background | ||
+ | Loading fs modules: [ 19.400000] fuse init (API version 7.8) | ||
+ | Success | ||
+ | [ 19.780000] ufsd: module license 'Commercial product' taints kernel. | ||
+ | [ 19.940000] ufsd: driver loaded at bf040000 built on Aug 5 2009 15:35:26 | ||
+ | [ 19.940000] UFSD version 7.07 (Aug 5 2009, 15:29:19) | ||
+ | [ 19.940000] NTFS read/write support included | ||
+ | [ 19.940000] Hfs+/HfsX read/write support included | ||
+ | [ 19.940000] $Id: ufsdvfs.c,v 1.226 2009/07/30 16:04:07 shura Exp $ (LBD=ON) | ||
+ | Loading tun.ko: [ 19.960000] tun: Universal TUN/TAP device driver, 1.6 | ||
+ | [ 19.970000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> | ||
+ | Success | ||
+ | Loading xce.ko: [ 19.990000] Cloud Engines XCE Init [Version: 1.0.0.20] | ||
+ | [ 20.000000] XCE: CPU MEMORY MAP: | ||
+ | [ 20.000000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings | ||
+ | [ 20.010000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space | ||
+ | [ 20.020000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram | ||
+ | [ 20.020000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space | ||
+ | [ 20.030000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space | ||
+ | [ 20.040000] XCE: Current GPIO State: | ||
+ | [ 20.040000] XCE: GPIO L OUT: 0xeff00000 | ||
+ | [ 20.050000] XCE: GPIO L OE: 0xefffffff | ||
+ | [ 20.050000] XCE: GPIO L BLINK: 0x00000000 | ||
+ | [ 20.060000] XCE: GPIO L POL: 0x00000000 | ||
+ | [ 20.060000] XCE: GPIO L IN: 0xeff00080 | ||
+ | [ 20.060000] XCE: GPIO H OUT: 0xfffeffff | ||
+ | [ 20.070000] XCE: GPIO H OE: 0xfffc3fff | ||
+ | [ 20.070000] XCE: GPIO H BLINK: 0x00000000 | ||
+ | [ 20.080000] XCE: GPIO H POL: 0x00000000 | ||
+ | [ 20.080000] XCE: GPIO H IN: 0x0002fffd | ||
+ | [ 20.080000] XCE: Kernel thread starting PID: 353 | ||
+ | Success | ||
+ | [ 20.090000] XCE: -- 'wdog=off | ||
+ | [ 20.090000] ' | ||
+ | Starting hbplug: Success | ||
+ | starting pid 355, tty '': '/bin/sh' | ||
+ | -sh-3.2# [ 21.080000] XCE: BLPARAMS: -- Loading properties [c707ff04]. | ||
+ | [ 21.090000] XCE: BLPARAMS: reading 2048 bytes @ a0000 | ||
+ | [ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a0800 | ||
+ | [ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a1000 | ||
+ | [ 21.110000] XCE: BLPARAMS: reading 2048 bytes @ a1800 | ||
+ | [ 26.290000] XCE: -- 'led0=0' |
Version vom 24. Dezember 2011, 16:34 Uhr
I am using a Seagate Freeagent Dockstar disk station as a fully fledged server at DB0ZM. Here are the pictures.
1 Pictures
2 Links
- http://ahsoftware.de/dockstar/
- http://www.rudiswiki.de/wiki/DockStarSerialLink
- http://blogdoch.net/index.php?entry=entry100405-203729 Installing Ubuntu
- http://www.yourwarrantyisvoid.com/2010/07/14/hardware-porn-seagate-dockstar-teardown/ good pictures!
3 Procedure
First you need to connecto to the serial port. For this purpose you use an Arduino style level shifter with 3,3V which you connect to the pins 6, 4, 2:
9 7 5 3 1 10 8 6 4 2 RX TX GND 3.3V!
So when you now boot up the device, you'll get the following output in the terminal (Linux: minicom):
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16) U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:256 MB CPU : Marvell Feroceon (Rev 1) CLOUD ENGINES BOARD: REDSTONE:1.0 Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x100000, size 0x300000 Reading data from 0x3ff800 -- 100% complete. 3145728 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-08-31 23:31:05 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1976384 Bytes = 1.9 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux............................................................................................................................ done, booting the kernel. [ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #57 Mon Aug 31 16:31:01 PDT 2009 [ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 [ 0.000000] Machine: Feroceon-KW [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] CPU0: D VIVT write-back cache [ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets [ 0.000000] Built 1 zonelists. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro [ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes) [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total [ 0.000000] Memory: 125824KB available (3588K code, 252K data, 120K init) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] NET: Registered protocol family 16 [ 0.240000] [ 0.240000] CPU Interface [ 0.240000] ------------- [ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB [ 0.240000] SDRAM_CS1 ....disable [ 0.240000] SDRAM_CS2 ....disable [ 0.240000] SDRAM_CS3 ....disable [ 0.240000] PEX0_MEM ....base e8000000, size 128MB [ 0.240000] PEX0_IO ....base f2000000, size 1MB [ 0.240000] INTER_REGS ....base f1000000, size 1MB [ 0.240000] NFLASH_CS ....base fa000000, size 2MB [ 0.240000] SPI_CS ....base f4000000, size 16MB [ 0.240000] BOOT_ROM_CS ....no such [ 0.240000] DEV_BOOTCS ....no such [ 0.240000] CRYPT_ENG ....base f0000000, size 2MB [ 0.240000] [ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE [ 0.240000] [ 0.240000] Detected Tclk 200000000 and SysClk 400000000 [ 0.240000] MV Buttons Device Load [ 0.240000] Marvell USB EHCI Host controller #0: c0537600 [ 0.740000] PEX0 interface detected no Link. [ 0.740000] PCI: bus0: Fast back to back transfers enabled [ 0.740000] SCSI subsystem initialized [ 0.740000] usbcore: registered new interface driver usbfs [ 0.740000] usbcore: registered new interface driver hub [ 0.740000] usbcore: registered new device driver usb [ 0.740000] NET: Registered protocol family 2 [ 0.750000] Time: kw_clocksource clocksource has been installed. [ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.840000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.840000] TCP reno registered [ 0.870000] RTC has been updated!!! [ 0.870000] RTC registered [ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions: [ 0.870000] o RAID 5 Xor calculation [ 0.870000] o kernel memcpy [ 0.870000] o kenrel memzero [ 0.870000] Number of XOR engines to use: 4 [ 0.870000] cesadev_init(c00116b4) [ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000 [ 0.870000] MV Buttons Driver Load [ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher [ 0.870000] squashfs: LZMA suppport for slax.org by jro [ 0.870000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc. [ 0.870000] io scheduler noop registered [ 0.870000] io scheduler anticipatory registered (default) [ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 0.900000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A [ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize [ 0.910000] Loading Marvell Ethernet Driver: [ 0.920000] o Cached descriptors in DRAM [ 0.920000] o DRAM SW cache-coherency [ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 0.940000] o TCP segmentation offload enabled [ 0.940000] o Receive checksum offload enabled [ 0.940000] o Transmit checksum offload enabled [ 0.950000] o Network Fast Processing (Routing) supported [ 0.960000] o Driver ERROR statistics enabled [ 0.960000] o Driver INFO statistics enabled [ 0.960000] o Proc tool API enabled [ 0.970000] o Rx descripors: q0=128 [ 0.970000] o Tx descripors: q0=532 [ 0.980000] o Loading network interface(s): [ 0.980000] o eth0, ifindex = 1, GbE port = 0 [ 0.990000] o eth1, ifindex = 2, GbE port = 1 [ 0.990000] [ 1.000000] mvFpRuleDb (c7ed5000): 1024 entries, 4096 bytes [ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 1.010000] Copyright (c) 1999-2006 Intel Corporation. [ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI [ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation [ 1.020000] [ 1.020000] Warning Sata is Powered Off [ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ [ 1.040000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) [ 1.050000] Scanning device for bad blocks [ 1.140000] Bad eraseblock 1825 at 0x0e420000 [ 1.150000] Using static partition definition [ 1.160000] Creating 4 MTD partitions on "nand_mtd": [ 1.160000] 0x00000000-0x00100000 : "u-boot" [ 1.170000] 0x00100000-0x00500000 : "uImage" [ 1.170000] 0x00500000-0x02500000 : "root" [ 1.180000] 0x02500000-0x10000000 : "data" [ 1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI [ 1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 [ 1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 [ 1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 1.250000] usb usb1: configuration #1 chosen from 1 choice [ 1.260000] hub 1-0:1.0: USB hub found [ 1.260000] hub 1-0:1.0: 1 port detected [ 1.380000] USB Universal Host Controller Interface driver v3.0 [ 1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2 [ 1.810000] usb 1-1: configuration #1 chosen from 1 choice [ 1.810000] hub 1-1:1.0: USB hub found [ 1.820000] hub 1-1:1.0: 4 ports detected [ 2.170000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3 [ 2.270000] usb 1-1.2: configuration #1 chosen from 1 choice [ 2.280000] usbcore: registered new interface driver usblp [ 2.280000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver [ 2.290000] Initializing USB Mass Storage driver... [ 2.300000] scsi0 : SCSI emulation for USB Mass Storage devices [ 2.300000] usbcore: registered new interface driver usb-storage [ 2.310000] USB Mass Storage support registered. [ 2.310000] mice: PS/2 mouse device common for all mice [ 2.320000] i2c /dev entries driver [ 2.320000] Linux telephony interface: v1.00 [ 2.330000] md: linear personality registered for level -1 [ 2.330000] md: raid0 personality registered for level 0 [ 2.340000] md: raid1 personality registered for level 1 [ 2.510000] raid6: int32x1 97 MB/s [ 2.680000] raid6: int32x2 114 MB/s [ 2.850000] raid6: int32x4 122 MB/s [ 3.020000] raid6: int32x8 110 MB/s [ 3.020000] raid6: using algorithm int32x4 (122 MB/s) [ 3.020000] md: raid6 personality registered for level 6 [ 3.030000] md: raid5 personality registered for level 5 [ 3.030000] md: raid4 personality registered for level 4 [ 3.040000] raid5: measuring checksumming speed [ 3.090000] arm4regs : 1084.000 MB/sec [ 3.140000] 8regs : 754.800 MB/sec [ 3.190000] 32regs : 899.600 MB/sec [ 3.190000] raid5: using function: arm4regs (1084.000 MB/sec) [ 3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com [ 3.200000] dm_crypt using the OCF package. [ 3.210000] sdhci: Secure Digital Host Controller Interface driver [ 3.210000] sdhci: Copyright(c) Pierre Ossman [ 3.220000] usbcore: registered new interface driver usbhid [ 3.220000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver [ 3.230000] TCP cubic registered [ 3.230000] NET: Registered protocol family 1 [ 3.240000] NET: Registered protocol family 17 [ 3.240000] md: Autodetecting RAID arrays. [ 3.250000] md: autorun ... [ 3.250000] md: ... autorun DONE. [ 7.870000] Empty flash at 0x00de8e44 ends at 0x00de9000 [ 8.030000] VFS: Mounted root (jffs2 filesystem) readonly. [ 8.030000] Freeing init memory: 120K [ 8.120000] scsi 0:0:0:0: Direct-Access USB DISK 2.0 PMAP PQ: 0 ANSI: 4 [ 8.950000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB) [ 8.960000] sd 0:0:0:0: [sda] Write Protect is off [ 8.960000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 9.010000] sd 0:0:0:0: [sda] 31277056 512-byte hardware sectors (16014 MB) [ 9.030000] sd 0:0:0:0: [sda] Write Protect is off [ 9.030000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 9.040000] sda: sda1 [ 9.270000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 9.270000] sd 0:0:0:0: Attached scsi generic sg0 type 0 init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST) starting pid 285, tty : '/etc/init.d/rcS' [ 10.200000] eth0: link down [ 10.200000] eth0: started udhcpc (v1.7.0) started HWADDR 00 0x10 0x75 0x1a 0xc0 0x57 PIP0 192 PIP1 87 Sending discover... [ 13.280000] eth0: link up, full duplex, speed 1 Gbps Sending discover... Sending discover... HWADDR 00 0x10 0x75 0x1a 0xc0 0x57 PIP0 192 PIP1 87 Unexpected Argument: leasefail interface=eth0 PATH=/sbin:/usr/sbin:/bin:/usr/bin PWD=/ SHLVL=1 HOME=/ _=/bin/printenv No lease, forking to background Loading fs modules: [ 19.400000] fuse init (API version 7.8) Success [ 19.780000] ufsd: module license 'Commercial product' taints kernel. [ 19.940000] ufsd: driver loaded at bf040000 built on Aug 5 2009 15:35:26 [ 19.940000] UFSD version 7.07 (Aug 5 2009, 15:29:19) [ 19.940000] NTFS read/write support included [ 19.940000] Hfs+/HfsX read/write support included [ 19.940000] $Id: ufsdvfs.c,v 1.226 2009/07/30 16:04:07 shura Exp $ (LBD=ON) Loading tun.ko: [ 19.960000] tun: Universal TUN/TAP device driver, 1.6 [ 19.970000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Success Loading xce.ko: [ 19.990000] Cloud Engines XCE Init [Version: 1.0.0.20] [ 20.000000] XCE: CPU MEMORY MAP: [ 20.000000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings [ 20.010000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space [ 20.020000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram [ 20.020000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space [ 20.030000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space [ 20.040000] XCE: Current GPIO State: [ 20.040000] XCE: GPIO L OUT: 0xeff00000 [ 20.050000] XCE: GPIO L OE: 0xefffffff [ 20.050000] XCE: GPIO L BLINK: 0x00000000 [ 20.060000] XCE: GPIO L POL: 0x00000000 [ 20.060000] XCE: GPIO L IN: 0xeff00080 [ 20.060000] XCE: GPIO H OUT: 0xfffeffff [ 20.070000] XCE: GPIO H OE: 0xfffc3fff [ 20.070000] XCE: GPIO H BLINK: 0x00000000 [ 20.080000] XCE: GPIO H POL: 0x00000000 [ 20.080000] XCE: GPIO H IN: 0x0002fffd [ 20.080000] XCE: Kernel thread starting PID: 353 Success [ 20.090000] XCE: -- 'wdog=off [ 20.090000] ' Starting hbplug: Success starting pid 355, tty : '/bin/sh' -sh-3.2# [ 21.080000] XCE: BLPARAMS: -- Loading properties [c707ff04]. [ 21.090000] XCE: BLPARAMS: reading 2048 bytes @ a0000 [ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a0800 [ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a1000 [ 21.110000] XCE: BLPARAMS: reading 2048 bytes @ a1800 [ 26.290000] XCE: -- 'led0=0'