Flashing OpenWRT to the WRTSL54GS: Unterschied zwischen den Versionen
Aus DL8RDS Wiki
Dl8rds (Diskussion | Beiträge) (New page: Flashing the WRTSL54GS was easy. Firmware version =>v2.07.2 killall: ntpclient: no process killed connect: Network is unreachable return code=1, from ntpclient Time update failed diag_l...) |
Dl8rds (Diskussion | Beiträge) |
||
| (5 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt) | |||
| Zeile 1: | Zeile 1: | ||
| − | Flashing the WRTSL54GS was easy. | + | Flashing the [[Cisco Linksys WRTSL54GS|WRTSL54GS]] was easy. I followed the instructions as given here: |
| + | * http://wiki.openwrt.org/OpenWrtDocs/Installing | ||
| − | + | I chose the simplest way by uploading the selected image through the device's firmware upgrade facility. Here comes a screen dump from the serial connection as established with my Level Shifter. But... I ran into troubles, but resolved them :-) Having a backdoor through the serial port, I got control of the CFE (Common Firmware Environment) and managed to flash the firmware, following the instructions given here: | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | * http://wiki.openwrt.org/OpenWrtDocs/Troubleshooting#head-457cc2f0848fb6600bae5dcab055a8431112c34e | ||
| + | * http://wiki.openwrt.org/OpenWrtDocs/Installing/TFTP | ||
| − | + | Also let me point you to the [[Connections between the MAX232 Level Shifter and the WRTSL54GS]] | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | No DPN | + | Firmware version =>v2.07.2 |
| − | et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0 | + | killall: ntpclient: no process killed |
| − | rndis0: Broadcom USB RNDIS Network Adapter (P-t-P) | + | connect: Network is unreachable |
| − | et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0 | + | return code=1, from ntpclient |
| − | CPU type 0x29006: 264MHz | + | Time update failed |
| − | Total memory: 32768 KBytes | + | diag_led_4704: Start GPIO 1 |
| − | + | http upgrading....umount all disks | |
| − | Total memory used by CFE: 0x80300000 - 0x803A3890 (669840) | + | Upgrading |
| − | Initialized Data: 0x803397A0 - 0x8033BEB0 (10000) | + | upgrade_ver[v2.8.1] upgrade_ver[20801] intel_ver[14108] 4712_ver[15000] |
| − | BSS Area: 0x8033BEB0 - 0x8033D890 (6624) | + | it's code.bin |
| − | Local Heap: 0x8033D890 - 0x803A1890 (409600) | + | code pattern correct! |
| − | Stack Area: 0x803A1890 - 0x803A3890 (8192) | + | freeram=[7270400] bufferram=[3235840] |
| − | Text (code) segment: 0x80300000 - 0x803397A0 (235424) | + | The free memory is enough, writing image once. |
| − | Boot area (physical): 0x003A4000 - 0x003E4000 | + | ..........................................................................................................................................................] |
| − | Relocation Factor: I:00000000 - D:00000000 | + | .linux: CRC OK |
| − | + | Writing image to flash, waiting a monent... | |
| − | Boot version: v3.5 | + | Amin 931006 (rc/mtd.c mtd_write) none adjust offset |
| − | The boot is CFE | + | Upgrading from web (http) now ... |
| − | + | ntp: nothing to do... | |
| − | mac_init(): Find mac [00:1D:7E:1E:9A:3B] in location 0 | + | done |
| − | Nothing... | + | diag_led_4704: Stop GPIO 1 |
| − | + | ej_langpack | |
| − | No eou key find | + | Terminated.................................... |
| − | Device eth0: hwaddr 00-1D-7E-1E-9A-3B, ipaddr 192.168.1.1, mask 255.255.255.0 | + | diag_led_4704: Start GPIO 1 |
| + | Sending SIGTERM to all processes | ||
| + | Sending SIGKILL to all processesRestarting system. | ||
| + | |||
| + | |||
| + | CFE version 1.0.37 for BCM947XX (32bit,SP,LE) | ||
| + | Build Date: Tue Feb 6 16:32:40 CST 2007 (root@linux) | ||
| + | Copyright (C) 2000,2001,2002,2003 Broadcom Corporation. | ||
| + | |||
| + | Initializing Arena | ||
| + | Initializing Devices. | ||
| + | |||
| + | No DPN | ||
| + | et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0 | ||
| + | rndis0: Broadcom USB RNDIS Network Adapter (P-t-P) | ||
| + | et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0 | ||
| + | CPU type 0x29006: 264MHz | ||
| + | Total memory: 32768 KBytes | ||
| + | |||
| + | Total memory used by CFE: 0x80300000 - 0x803A3890 (669840) | ||
| + | Initialized Data: 0x803397A0 - 0x8033BEB0 (10000) | ||
| + | BSS Area: 0x8033BEB0 - 0x8033D890 (6624) | ||
| + | Local Heap: 0x8033D890 - 0x803A1890 (409600) | ||
| + | Stack Area: 0x803A1890 - 0x803A3890 (8192) | ||
| + | Text (code) segment: 0x80300000 - 0x803397A0 (235424) | ||
| + | Boot area (physical): 0x003A4000 - 0x003E4000 | ||
| + | Relocation Factor: I:00000000 - D:00000000 | ||
| + | |||
| + | Boot version: v3.5 | ||
| + | The boot is CFE | ||
| + | |||
| + | mac_init(): Find mac [00:1D:7E:1E:9A:3B] in location 0 | ||
| + | Nothing... | ||
| + | |||
| + | No eou key find | ||
| + | Device eth0: hwaddr 00-1D-7E-1E-9A-3B, ipaddr 192.168.1.1, mask 255.255.255.0 | ||
gateway not set, nameserver not set | gateway not set, nameserver not set | ||
| − | Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) | + | Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) |
| − | Loading: .. 3704 bytes read | + | Loading: .. 3704 bytes read |
| − | Entry at 0x80001000 | + | Entry at 0x80001000 |
| − | Closing network. | + | Closing network. |
| − | Starting program at 0x80001000 | + | Starting program at 0x80001000 |
| − | CPU revision is: 00029006 | + | CPU revision is: 00029006 |
| − | Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes. | + | Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes. |
| − | Primary data cache 16kB, 2-way, linesize 16 bytes. | + | Primary data cache 16kB, 2-way, linesize 16 bytes. |
| − | Linux version 2.4.30 (nbd@ds10) (gcc version 3.4.4 (OpenWrt-1.0)) #1 Sat Feb 3 13:16:08 CET 2007 | + | Linux version 2.4.30 (nbd@ds10) (gcc version 3.4.4 (OpenWrt-1.0)) #1 Sat Feb 3 13:16:08 CET 2007 |
| − | Setting the PFC value as 0x15 | + | Setting the PFC value as 0x15 |
| − | Determined physical RAM map: | + | Determined physical RAM map: |
| − | + | memory: 02000000 @ 00000000 (usable) | |
| − | On node 0 totalpages: 8192 | + | On node 0 totalpages: 8192 |
| − | zone(0): 8192 pages. | + | zone(0): 8192 pages. |
| − | zone(1): 0 pages. | + | zone(1): 0 pages. |
| − | zone(2): 0 pages. | + | zone(2): 0 pages. |
| − | Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200 | + | Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd |
| − | CPU: BCM4704 rev 9 at 264 MHz | + | console=ttyS0,115200 |
| − | Using 132.000 MHz high precision timer. | + | CPU: BCM4704 rev 9 at 264 MHz |
| − | Calibrating delay loop... 263.78 BogoMIPS | + | Using 132.000 MHz high precision timer. |
| − | Memory: 30436k/32768k available (1455k kernel code, 2332k reserved, 104k data, 80k init, 0k highmem) | + | Calibrating delay loop... 263.78 BogoMIPS |
| − | Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) | + | Memory: 30436k/32768k available (1455k kernel code, 2332k reserved, 104k data, 80k init, 0k highmem) |
| − | Inode cache hash table entries: 2048 (order: 2, 16384 bytes) | + | Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) |
| − | Mount cache hash table entries: 512 (order: 0, 4096 bytes) | + | Inode cache hash table entries: 2048 (order: 2, 16384 bytes) |
| − | Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) | + | Mount cache hash table entries: 512 (order: 0, 4096 bytes) |
| − | Page-cache hash table entries: 8192 (order: 3, 32768 bytes) | + | Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) |
| − | Checking for 'wait' instruction... unavailable. | + | Page-cache hash table entries: 8192 (order: 3, 32768 bytes) |
| − | POSIX conformance testing by UNIFIX | + | Checking for 'wait' instruction... unavailable. |
| − | PCI: Fixing up bus 0 | + | POSIX conformance testing by UNIFIX |
| − | PCI: Fixing up bridge | + | PCI: Fixing up bus 0 |
| − | PCI: Fixing up bus 1 | + | PCI: Fixing up bridge |
| − | Linux NET4.0 for Linux 2.4 | + | PCI: Fixing up bus 1 |
| − | Based upon Swansea University Computer Society NET3.039 | + | Linux NET4.0 for Linux 2.4 |
| − | Initializing RT netlink socket | + | Based upon Swansea University Computer Society NET3.039 |
| − | Starting kswapd | + | Initializing RT netlink socket |
| − | Registering mini_fo version $Id$ | + | Starting kswapd |
| − | devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) | + | Registering mini_fo version $Id$ |
| − | devfs: boot_options: 0x1 | + | devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) |
| − | JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. | + | devfs: boot_options: 0x1 |
| − | Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher | + | JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB. |
| − | pty: 256 Unix98 ptys configured | + | Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher |
| − | Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled | + | pty: 256 Unix98 ptys configured |
| − | ttyS00 at 0xb8000300 (irq = 3) is a 16550A | + | Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled |
| − | ttyS01 at 0xb8000400 (irq = 0) is a 16550A | + | ttyS00 at 0xb8000300 (irq = 3) is a 16550A |
| − | b44.c:v0.93 (Mar, 2004) | + | ttyS01 at 0xb8000400 (irq = 0) is a 16550A |
| − | eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1d:7e:1e:9a:3b | + | b44.c:v0.93 (Mar, 2004) |
| − | eth1: Broadcom 47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b | + | eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1d:7e:1e:9a:3b |
| − | cfi_cmdset_0001: Erase suspend on write enabled | + | eth1: Broadcom 47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b |
| − | Using buffer write method | + | cfi_cmdset_0001: Erase suspend on write enabled |
| − | Flash device: 0x800000 at 0x1c000000 | + | Using buffer write method |
| − | bootloader size: 262144 | + | Flash device: 0x800000 at 0x1c000000 |
| − | Physically mapped flash: Filesystem type: squashfs, size=0xfb158 | + | bootloader size: 262144 |
| − | Updating TRX offsets and length: | + | Physically mapped flash: Filesystem type: squashfs, size=0xfb158 |
| − | old trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x0017a000 crc32=0x1f181132 | + | Updating TRX offsets and length: |
| − | new trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x00180000 crc32=0x9cbb6f33 | + | old trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x0017a000 crc32=0x1f181132 |
| − | Done | + | new trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x00180000 crc32=0x9cbb6f33 |
| − | Creating 5 MTD partitions on "Physically mapped flash": | + | Done |
| − | 0x00000000-0x00040000 : "cfe" | + | Creating 5 MTD partitions on "Physically mapped flash": |
| − | 0x00040000-0x007e0000 : "linux" | + | 0x00000000-0x00040000 : "cfe" |
| − | 0x000be400-0x001c0000 : "rootfs" | + | 0x00040000-0x007e0000 : "linux" |
| − | mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only | + | 0x000be400-0x001c0000 : "rootfs" |
| − | 0x007e0000-0x00800000 : "nvram" | + | mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only |
| − | 0x001c0000-0x007e0000 : "OpenWrt" | + | 0x007e0000-0x00800000 : "nvram" |
| − | Initializing Cryptographic API | + | 0x001c0000-0x007e0000 : "OpenWrt" |
| − | NET4: Linux TCP/IP 1.0 for NET4.0 | + | Initializing Cryptographic API |
| − | IP Protocols: ICMP, UDP, TCP, IGMP | + | NET4: Linux TCP/IP 1.0 for NET4.0 |
| − | IP: routing cache hash table of 512 buckets, 4Kbytes | + | IP Protocols: ICMP, UDP, TCP, IGMP |
| − | TCP: Hash tables configured (established 2048 bind 4096) | + | IP: routing cache hash table of 512 buckets, 4Kbytes |
| − | ip_conntrack version 2.1 (5953 buckets, 5953 max) - 332 bytes per conntrack | + | TCP: Hash tables configured (established 2048 bind 4096) |
| − | ip_tables: (C) 2000-2002 Netfilter core team | + | ip_conntrack version 2.1 (5953 buckets, 5953 max) - 332 bytes per conntrack |
| − | NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. | + | ip_tables: (C) 2000-2002 Netfilter core team |
| − | NET4: Ethernet Bridge 008 for NET4.0 | + | NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
| − | 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> | + | NET4: Ethernet Bridge 008 for NET4.0 |
| − | All bugs added by David S. Miller <davem@redhat.com> | + | 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> |
| − | VFS: Mounted root (squashfs filesystem) readonly. | + | All bugs added by David S. Miller <davem@redhat.com> |
| − | Mounted devfs on /dev | + | VFS: Mounted root (squashfs filesystem) readonly. |
| − | Freeing unused kernel memory: 80k freed | + | Mounted devfs on /dev |
| − | Algorithmics/MIPS FPU Emulator v1.5 | + | Freeing unused kernel memory: 80k freed |
| − | Using /lib/modules/2.4.30/diag.o | + | Algorithmics/MIPS FPU Emulator v1.5 |
| − | diag: Detected 'Linksys WRTSL54GS' | + | Using /lib/modules/2.4.30/diag.o |
| − | Using /lib/modules/2.4.30/switch-core.o | + | diag: Detected 'Linksys WRTSL54GS' |
| − | Using /lib/modules/2.4.30/switch-robo.o | + | Using /lib/modules/2.4.30/switch-core.o |
| − | Probing device eth0: found! | + | Using /lib/modules/2.4.30/switch-robo.o |
| − | b44: eth0: Link is up at 100 Mbps, full duplex. | + | Probing device eth0: found! |
| − | b44: eth0: Flow control is off for TX and off for RX. | + | b44: eth0: Link is up at 100 Mbps, full duplex. |
| − | Unlocking linux ... | + | b44: eth0: Flow control is off for TX and off for RX. |
| − | jffs2 not ready yet; using ramdisk | + | Unlocking linux ... |
| − | mini_fo: using base directory: / | + | jffs2 not ready yet; using ramdisk |
| − | mini_fo: using storage directory: /tmp/root | + | mini_fo: using base directory: / |
| − | init started: BusyBox v1.00 (2007.01.30-11:42+0000) multi-call binary | + | mini_fo: using storage directory: /tmp/root |
| − | + | init started: BusyBox v1.00 (2007.01.30-11:42+0000) multi-call binary | |
| − | Please press Enter to activate this console. jffs2.bbc: SIZE compression mode activated. | + | |
| − | PCI: Enabling device 01:01.0 (0004 -> 0006) | + | Please press Enter to activate this console. jffs2.bbc: SIZE compression mode activated. |
| − | eth2: Broadcom BCM4318 802.11 Wireless Controller 3.90.37.0 | + | PCI: Enabling device 01:01.0 (0004 -> 0006) |
| − | BFL_ENETADM not set in boardflags. Use force=1 to ignore. | + | eth2: Broadcom BCM4318 802.11 Wireless Controller 3.90.37.0 |
| − | device eth0 entered promiscuous mode | + | BFL_ENETADM not set in boardflags. Use force=1 to ignore. |
| − | b44: eth0: Link is up at 100 Mbps, full duplex. | + | device eth0 entered promiscuous mode |
| − | b44: eth0: Flow control is off for TX and off for RX. | + | b44: eth0: Link is up at 100 Mbps, full duplex. |
| − | device eth2 entered promiscuous mode | + | b44: eth0: Flow control is off for TX and off for RX. |
| − | br0: port 2(eth2) entering learning state | + | device eth2 entered promiscuous mode |
| − | br0: port 1(eth0) entering learning state | + | br0: port 2(eth2) entering learning state |
| − | br0: port 2(eth2) entering forwarding state | + | br0: port 1(eth0) entering learning state |
| − | br0: topology change detected, propagating | + | br0: port 2(eth2) entering forwarding state |
| − | br0: port 1(eth0) entering forwarding state | + | br0: topology change detected, propagating |
| − | br0: topology change detected, propagating | + | br0: port 1(eth0) entering forwarding state |
| − | b44: eth1: Link is up at 100 Mbps, full duplex. | + | br0: topology change detected, propagating |
| − | b44: eth1: Flow control is off for TX and off for RX. | + | b44: eth1: Link is up at 100 Mbps, full duplex. |
| − | ^H^H | + | b44: eth1: Flow control is off for TX and off for RX. |
| − | + | ^H^H | |
| − | + | ||
| − | BusyBox v1.00 (2007.01.30-11:42+0000) Built-in shell (ash) | + | |
| − | Enter 'help' for a list of built-in commands. | + | BusyBox v1.00 (2007.01.30-11:42+0000) Built-in shell (ash) |
| − | + | Enter 'help' for a list of built-in commands. | |
| − | + | ||
| − | + | _______ ________ __ | |
| − | + | | |.-----.-----.-----.| | | |.----.| |_ | |
| − | + | | - || _ | -__| || | | || _|| _| | |
| − | + | |_______|| __|_____|__|__||________||__| |____| | |
| − | + | |__| W I R E L E S S F R E E D O M | |
| − | + | WHITE RUSSIAN (0.9) ------------------------------- | |
| − | + | * 2 oz Vodka Mix the Vodka and Kahlua together | |
| − | + | * 1 oz Kahlua over ice, then float the cream or | |
| − | + | * 1/2oz cream milk on the top. | |
| − | root@OpenWrt:/# ls | + | --------------------------------------------------- |
| − | bin dev etc jffs lib mnt proc rom sbin tmp usr var www | + | root@OpenWrt:/# ls |
| − | root@OpenWrt:/# ls -al | + | bin dev etc jffs lib mnt proc rom sbin tmp usr var www |
| − | drwxr-xr-x 2 root root 40 Jan 1 00:00 . | + | root@OpenWrt:/# ls -al |
| − | drwxr-xr-x 2 root root 40 Jan 1 00:00 .. | + | drwxr-xr-x 2 root root 40 Jan 1 00:00 . |
| − | drwxr-xr-x 1 root root 384 Jan 30 2007 bin | + | drwxr-xr-x 2 root root 40 Jan 1 00:00 .. |
| − | drwxr-xr-x 1 root root 0 Jan 1 1970 dev | + | drwxr-xr-x 1 root root 384 Jan 30 2007 bin |
| − | drwxr-xr-x 1 root root 287 Feb 3 2007 etc | + | drwxr-xr-x 1 root root 0 Jan 1 1970 dev |
| − | drwxr-xr-x 1 root root 0 Feb 3 2007 jffs | + | drwxr-xr-x 1 root root 287 Feb 3 2007 etc |
| − | drwxr-xr-x 1 root root 322 Feb 3 2007 lib | + | drwxr-xr-x 1 root root 0 Feb 3 2007 jffs |
| − | drwxr-xr-x 1 root root 0 Feb 3 2007 mnt | + | drwxr-xr-x 1 root root 322 Feb 3 2007 lib |
| − | dr-xr-xr-x 35 root root 0 Jan 1 00:00 proc | + | drwxr-xr-x 1 root root 0 Feb 3 2007 mnt |
| − | drwxr-xr-x 1 root root 85 Feb 3 2007 rom | + | dr-xr-xr-x 35 root root 0 Jan 1 00:00 proc |
| − | drwxr-xr-x 1 root root 240 Feb 3 2007 sbin | + | drwxr-xr-x 1 root root 85 Feb 3 2007 rom |
| − | drwxrwxrwt 7 root root 220 Jan 1 00:00 tmp | + | drwxr-xr-x 1 root root 240 Feb 3 2007 sbin |
| − | drwxr-xr-x 1 root root 31 Jan 30 2007 usr | + | drwxrwxrwt 7 root root 220 Jan 1 00:00 tmp |
| − | lrwxrwxrwx 1 root root 4 Feb 3 2007 var -> /tmp | + | drwxr-xr-x 1 root root 31 Jan 30 2007 usr |
| − | drwxr-xr-x 1 root root 62 Feb 3 2007 www | + | lrwxrwxrwx 1 root root 4 Feb 3 2007 var -> /tmp |
| − | root@OpenWrt:/# df -k | + | drwxr-xr-x 1 root root 62 Feb 3 2007 www |
| − | Filesystem 1k-blocks Used Available Use% Mounted on | + | root@OpenWrt:/# df -k |
| − | /dev/root 1024 1024 0 100% /rom | + | Filesystem 1k-blocks Used Available Use% Mounted on |
| − | none 15256 28 15228 0% /tmp | + | /dev/root 1024 1024 0 100% /rom |
| − | /tmp/root 1024 1024 0 100% / | + | none 15256 28 15228 0% /tmp |
| − | root@OpenWrt:/# | + | /tmp/root 1024 1024 0 100% / |
| + | root@OpenWrt:/# | ||
Aktuelle Version vom 12. April 2008, 16:26 Uhr
Flashing the WRTSL54GS was easy. I followed the instructions as given here:
I chose the simplest way by uploading the selected image through the device's firmware upgrade facility. Here comes a screen dump from the serial connection as established with my Level Shifter. But... I ran into troubles, but resolved them :-) Having a backdoor through the serial port, I got control of the CFE (Common Firmware Environment) and managed to flash the firmware, following the instructions given here:
- http://wiki.openwrt.org/OpenWrtDocs/Troubleshooting#head-457cc2f0848fb6600bae5dcab055a8431112c34e
- http://wiki.openwrt.org/OpenWrtDocs/Installing/TFTP
Also let me point you to the Connections between the MAX232 Level Shifter and the WRTSL54GS
Firmware version =>v2.07.2
killall: ntpclient: no process killed
connect: Network is unreachable
return code=1, from ntpclient
Time update failed
diag_led_4704: Start GPIO 1
http upgrading....umount all disks
Upgrading
upgrade_ver[v2.8.1] upgrade_ver[20801] intel_ver[14108] 4712_ver[15000]
it's code.bin
code pattern correct!
freeram=[7270400] bufferram=[3235840]
The free memory is enough, writing image once.
..........................................................................................................................................................]
.linux: CRC OK
Writing image to flash, waiting a monent...
Amin 931006 (rc/mtd.c mtd_write) none adjust offset
Upgrading from web (http) now ...
ntp: nothing to do...
done
diag_led_4704: Stop GPIO 1
ej_langpack
Terminated....................................
diag_led_4704: Start GPIO 1
Sending SIGTERM to all processes
Sending SIGKILL to all processesRestarting system.
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 6 16:32:40 CST 2007 (root@linux)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing Devices.
No DPN
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0
rndis0: Broadcom USB RNDIS Network Adapter (P-t-P)
et1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.38.0
CPU type 0x29006: 264MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80300000 - 0x803A3890 (669840)
Initialized Data: 0x803397A0 - 0x8033BEB0 (10000)
BSS Area: 0x8033BEB0 - 0x8033D890 (6624)
Local Heap: 0x8033D890 - 0x803A1890 (409600)
Stack Area: 0x803A1890 - 0x803A3890 (8192)
Text (code) segment: 0x80300000 - 0x803397A0 (235424)
Boot area (physical): 0x003A4000 - 0x003E4000
Relocation Factor: I:00000000 - D:00000000
Boot version: v3.5
The boot is CFE
mac_init(): Find mac [00:1D:7E:1E:9A:3B] in location 0
Nothing...
No eou key find
Device eth0: hwaddr 00-1D-7E-1E-9A-3B, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3704 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00029006
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Linux version 2.4.30 (nbd@ds10) (gcc version 3.4.4 (OpenWrt-1.0)) #1 Sat Feb 3 13:16:08 CET 2007
Setting the PFC value as 0x15
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd
console=ttyS0,115200
CPU: BCM4704 rev 9 at 264 MHz
Using 132.000 MHz high precision timer.
Calibrating delay loop... 263.78 BogoMIPS
Memory: 30436k/32768k available (1455k kernel code, 2332k reserved, 104k data, 80k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Fixing up bus 1
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Registering mini_fo version $Id$
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 3) is a 16550A
ttyS01 at 0xb8000400 (irq = 0) is a 16550A
b44.c:v0.93 (Mar, 2004)
eth0: Broadcom 47xx 10/100BaseT Ethernet 00:1d:7e:1e:9a:3b
eth1: Broadcom 47xx 10/100BaseT Ethernet 00:90:4c:60:00:2b
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Flash device: 0x800000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0xfb158
Updating TRX offsets and length:
old trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x0017a000 crc32=0x1f181132
new trx = [0x0000001c, 0x000008d8, 0x0007e400], len=0x00180000 crc32=0x9cbb6f33
Done
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007e0000 : "linux"
0x000be400-0x001c0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007e0000-0x00800000 : "nvram"
0x001c0000-0x007e0000 : "OpenWrt"
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (5953 buckets, 5953 max) - 332 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 80k freed
Algorithmics/MIPS FPU Emulator v1.5
Using /lib/modules/2.4.30/diag.o
diag: Detected 'Linksys WRTSL54GS'
Using /lib/modules/2.4.30/switch-core.o
Using /lib/modules/2.4.30/switch-robo.o
Probing device eth0: found!
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Unlocking linux ...
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
init started: BusyBox v1.00 (2007.01.30-11:42+0000) multi-call binary
Please press Enter to activate this console. jffs2.bbc: SIZE compression mode activated.
PCI: Enabling device 01:01.0 (0004 -> 0006)
eth2: Broadcom BCM4318 802.11 Wireless Controller 3.90.37.0
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
device eth0 entered promiscuous mode
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
device eth2 entered promiscuous mode
br0: port 2(eth2) entering learning state
br0: port 1(eth0) entering learning state
br0: port 2(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
b44: eth1: Link is up at 100 Mbps, full duplex.
b44: eth1: Flow control is off for TX and off for RX.
^H^H
BusyBox v1.00 (2007.01.30-11:42+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
WHITE RUSSIAN (0.9) -------------------------------
* 2 oz Vodka Mix the Vodka and Kahlua together
* 1 oz Kahlua over ice, then float the cream or
* 1/2oz cream milk on the top.
---------------------------------------------------
root@OpenWrt:/# ls
bin dev etc jffs lib mnt proc rom sbin tmp usr var www
root@OpenWrt:/# ls -al
drwxr-xr-x 2 root root 40 Jan 1 00:00 .
drwxr-xr-x 2 root root 40 Jan 1 00:00 ..
drwxr-xr-x 1 root root 384 Jan 30 2007 bin
drwxr-xr-x 1 root root 0 Jan 1 1970 dev
drwxr-xr-x 1 root root 287 Feb 3 2007 etc
drwxr-xr-x 1 root root 0 Feb 3 2007 jffs
drwxr-xr-x 1 root root 322 Feb 3 2007 lib
drwxr-xr-x 1 root root 0 Feb 3 2007 mnt
dr-xr-xr-x 35 root root 0 Jan 1 00:00 proc
drwxr-xr-x 1 root root 85 Feb 3 2007 rom
drwxr-xr-x 1 root root 240 Feb 3 2007 sbin
drwxrwxrwt 7 root root 220 Jan 1 00:00 tmp
drwxr-xr-x 1 root root 31 Jan 30 2007 usr
lrwxrwxrwx 1 root root 4 Feb 3 2007 var -> /tmp
drwxr-xr-x 1 root root 62 Feb 3 2007 www
root@OpenWrt:/# df -k
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/root 1024 1024 0 100% /rom
none 15256 28 15228 0% /tmp
/tmp/root 1024 1024 0 100% /
root@OpenWrt:/#
